国产精品18禁污污网站,亚洲一区二区三区偷拍女厕,国产自产V一区二区三区C,国产精品天干天干综合网

Welcome [Wuxi Yi Jin Machinery Co. Ltd.] official website!
Chinese   |   English   |  Sitemap
Explosion proof

Position:Home > Explosion proof >

  • B4-72C

    B4-72C

    MORE+

  • B4-72C

    B4-72C

    MORE+

  • B4-72C

    B4-72C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

 Centrifugal fan in the end is how to install, centrifugal fan manufacturers of workers is described as follows:
1. Centrifugal fan of the overall unit installation, should be placed directly on the basis of pairs of oblique horn leveling.
2. On-site assembly of the centrifugal fan, the base of the cutting surface should be properly protected, there should be no corrosion or operation, the base placed on the basis of the application of pairs of oblique horn leveling.
3. The bearing seat and the base should be tightly engaged, the vertical non-level should not exceed 0.2 / 1000, with the level on the spindle measurement, horizontal horizontal water should not exceed 0.3 / 1000, with the level of the bearing in the level of the sub-surface measuring.
4. Before the bearing grinding, the rotor axis should be corrected with the axis of the chassis, and the gap between the impeller and the inlet and the clearance between the spindle and the rear side of the housing should be adjusted to match the equipment technology The provisions of the document.
5. When the spindle and the bearing are assembled, they should be inspected according to the equipment technical documents. Bearing bearing and bearing pad should be maintained between 0.03-0.04 mm interference.
6. When the fan housing is assembled, the position of the housing should be determined on the basis of the rotor axis and the axial and radial clearance between the inlet of the impeller and the air inlet of the cabinet should be high and within the specified range. Whether the anchor bolts are fastened. If the gap is not specified in the technical documentation, the general axial clearance shall be 1/100 of the outer diameter of the impeller. The radial clearance shall be evenly distributed. The value shall be 1.5 / 1000-3 / 1000 of the outer diameter of the impeller. Adjust the value of the gap to try to improve the efficiency of the fan.
7. When the fan is correct, the fan shaft and the motor shaft of different degrees of axis: radial displacement should not exceed 0.05 mm, the tilt should not exceed 0.2 / 1000.
8. Rolling bearing assembly of the centrifugal fan, the two bearing frame on the bearing hole of different shaft degrees, until the rotor is installed, to flexible rotation prevail.

Contact: Mr. Wei 180 6833 7327 / 133 9518 5578 7 ????Tel: 0510-83303276 ????Fax: 0510-83303276

E-mail: 2637472470@qq.com ????Web: www.meethatv.com ????Add: Luoxian Town, Huishan District, Wuxi City

Copy right ? 2017 Wuxi Yi Jin Machinery Co., Ltd. All Rights Reserved

主站蜘蛛池模板: 亚洲AV人人澡人人爽人人夜夜| 中文字幕人妻无码精品| AAAAAA级丝袜美女片| 中文字幕日韩久久综合影院| 国产嫖妓露脸在线播放| 国产18禁黄网站免费观看| 国产成人久久精品麻豆二区| 国产乱码精品一区二区三区中文| 精品无码久久久久国产| 精品欧美一区二区在线观看| 一区二区欧美| 亚洲精品一区二区三区四区五区| 色94色欧美sute亚洲线路二| 国产a精品人成视频免费| 亚洲日本天堂影院在线观看| 人妻无码人妻有码中文字幕在线| 欧美性猛片AAAAAAA做受| 久久婷婷五月综合97色一本一本| 无码高潮抽搐流白浆喷水| 欧美肛交视频一区在线观看| 亚洲国产精品色婷婷| 午夜福利无遮挡A欧美| 18成禁人视频免费午夜影视| 18以下岁禁止1000部免费| 中文字幕爆乳巨爆乳系列无码| 日韩AV女优国产小电影在线观看| 国产AV无码专区亚洲精品网站| julia无码人妻中文字幕在线| 午夜福利久久久噜久噜久久综合| 超碰AV女优| 欧美牲交a欧美牲交| 亚洲最大看欧美片网站| 爱爱小说久久视频| 国产乱码精品一区二区三区四川人| 漂亮人妻被黑人久久精品| 少妇高潮喷水久久久久久久久久| 7777精品伊人久久久大香线蕉超级流畅| 艳妇荡岳丰满交换做爰| 国产做爰XXXⅩ高潮电影| 久久久久人妻一区精品性色av| 国产免费女优|
在线咨询
客服1
客服2
请您留言

感谢您的关注,当前客服人员不在线,请填写一下您的信息,我们会尽快和您联系。

提交